Search Results

To solve the problem of serious roller wear and improve the smoothness of the sliding door motion process, the rigid-flexible coupling multi-body model of the vehicle sliding door was built in ADAMS. Force boundary conditions of the model were determined to meet the speed requirement of monitoring point and time requirement of door opening-closing process according to the bench test specification. The results of dynamic simulation agreed well with that of test so the practicability and credibility of the model was verified. In the optimization of the ride comfort of the sliding door, two different schemes were proposed. The one was to optimize the position of hinge pivots and the other was to optimize the structural parameters of the middle guide. The impact load of lead roller on middle guide, the curvature of the motion trajectory and angular acceleration of the sliding door centroid were taken as optimization objectives.

For an innovative opposed-piston diesel engine (OPE) with two-stroke operation mode, it attracted even more attentions than ever in some developed countries all around the world, attributed to the unique advantages of higher power density that conducive to downsize IC engine, as well as the potential of further reducing fuel consumption for outstanding thermal efficiency. To achieve fast practical application and ensure the feasibility in concept design stage, the performance characteristic of OPE crankshaft system was investigated, and thus a theoretical analytic model of crankshaft system in an OP2S (Opposed-piston two stroke) engine was established. The effects of all structural design variables on averaged output torque of OPE crankshaft were analyzed, respectively. It was found that the initial crank angle difference between inner crank web and outer crank web was considered as a most critical contributor to boost the averaged torque output than other design variables.

Different choices of IGBTs’ switching frequency of the PMSM inverter used in vehicle lead to different energy loss of the inverter. Meanwhile, they lead to different phase current harmonics, which result in different energy loss of the PMSM. Compared with traditional switching frequency design method, the optimal design method considers the loss of the PMSM as well as the inverter, proposing a minimum system loss switching frequency design method. Firstly, by establishing the IGBT model (Hefner Model) and the PMSM analytical model, obtain PMSM phase currents under different switching frequencies through simulating. The inverter energy loss is obtained at the same time. Then, the phase currents under different conditions are applied to the finite element model to obtain the distribution of the magnetic field strength H and the magnetic induction B, so that the PMSM loss can be calculated.

As one of the most crucial components in electric vehicles, power batteries generate abundant heat during charging and discharging processes. Thermal management system (TMS), which is designed to keep the battery cells within an optimum temperature range and to maintain an even temperature distribution from cell to cell, is vital for the high efficiency, long calendar life and reliable safety of these power batteries. With the desirable features of low system complexity, light weight, high energy efficiency and good battery thermal uniformity, thermal management using composite phase change materials (PCMs) has drawn great attention in the past fifteen years. In the hope of supplying helpful guidelines for the design of the PCM-based TMSs, this work begins with the summarization of the most commonly applied heat transfer enhancement methods (i.e., the use of thermally conductive particles, metal fin, expanded graphite matrix and metal foam) for PCMs by different researchers.

The statement of the engine shake problem is presented through comparing the quarter vehicle models with the rigid-connected and flexible-connected powertrain which is supported on the body by a rubber mount. Then the model is extended by replacing the rubber mount as a hydraulic engine mount (HEM) with regard to the inertia and resistance of the fluid within the inertia track. Based on these, a full vehicle model with 14 degree of freedoms (DOFs) is proposed to calculate the engine shake, which consists of 6 of the powertrain, 1 of the fluid within the inertia track of the HEM, 3 of the car body and 4 of the unsprung mass. Simulation analysis based on the proposed model is implemented, through which the conclusion is drawn that the HEM has great influence on the body and seat track response subjected to front wheel inputs, compared with the rubber mount.

Recent toxicological and epidemiologic studies have shown that diesel emissions have been a significant toxic air contaminant. Catalyzed DPF (CDPF) not only significantly reduces the PM mass emissions (>90%), but also further promotes carrier self-regeneration and oxidize more harmful gaseous pollutants by the catalyst coated on the carrier. However, some ultrafine particles and potentially harmful gaseous pollutants, such as VOCs species, originally emitted in the vapor-phase at high plume temperature, may penetrate through the CDPF filter. Furthermore, the components and content of catalyst coated on the CDPF could influence the physicochemical properties and toxicity intensity of those escaping ultrafine particles and gaseous pollutants. In this work, (1) we investigated the influence of precious metal content as a variable parameter on the physicochemical properties and catalytic activities of the small CDPF samples.

Electric vehicle driving permanent magnet synchronous motor has a wide speed range and load changes, with abundant harmonic currents, and its eccentric form is complex, which all result in poor sound quality and abnormal noise problems becoming increasingly prominent. To make a systematic and thorough study of the centralized drive permanent magnet synchronous motor (PMSM) is significant to ameliorate the sound quality and solve noise problems. MATLAB-based modeling technology, SPSS software, and the establishment of sound quality evaluation model for the centralized drive PMSM has a crucial reference value on the research and development of the electric vehicle driving permanent magnet synchronous motor. As for the sound quality of centralized drive PMSM, firstly, in order to get objective parameter values, evaluation models of objective parameters based on psychological acoustics should be established after the collection of the sound samples.

The maximum equivalent plastic strain (EPSmax), which can be achieved in the gauge region of a cruciform specimen during in-plane biaxial tensile tests, is limited due to early fracture on the cruciform specimen arm. In this paper, a theoretical model was proposed to determine the factors related to the EPSmax of a cruciform specimen following ISO 16842: 2014. Biaxial tensile tests were carried out to verify the theoretical analyses. Results show that the material strength coefficient (k) has no effect on the EPSmax, and EPSmax increases with the increase of the material hardening exponent (n) and the cross-sectional-area ratio (c) of the arm region to the gauge region. It is found that the applied load ratio (α) has an effect on EPSmax, which decreases as the load ratio increases from 0:1 (i.e. uniaxial tension) to 1:2 (i.e. plane strain state) and then increases as the load ratio increases to 1:1 (i.e. balanced biaxial tension).

Fatigue defect and failure of rubber element widely used in mechanical systems could seriously affect the safety and reliability of systems in practical operation. Because rubber element is considered as hyperelastic material, traditional σ - N curve which is usually used in metal material for fatigue life analysis can not be used here. The fatigue life of rubber bushing in automobile engine cradle was analyzed by using the energy method. The Yeoh model coefficients were given by tensile test of natural rubber, and the estimating formula for fatigue life of natural rubber was obtained by finite element calculation and fatigue test. Maximum strain energy density was treated as the parameter of fatigue damage, then the rubber bushing fatigue life was calculated by the estimating formula. The results were verified by test of rubber bushing, which indicated that the model mentioned in this paper is accuracy enough.

Indirect rotary transducer for an automotive screen interface is an innovative solution for the smart cockpit. The primary objective of this study is to design an indirect rotary transducer system, and study its feasibility in the smart cockpit. The working theory of this designed system is that the magnetic induction hall electronic chip can detect changes in the magnetic field. Several tests have been conducted, which show that the hypothesis of dangling operating system achieves the same effect as a hard-wired operating system. The results of the experiment indicate that the magnetic induction hall sensor can meet the specification of traditional hard-wired operating system. This system is a good concept for intelligent cab driving, which can fully meet the needs of the current market.

An online fault detection and isolation (FDI) method for several common sensor faults and even demagnetization of PMSM is proposed by combining model-based and signal analysis technology. To begin with, the field reconstruction method (FRM) of PMSM is employed to obtain the flux residuals which are used as the criterion of fault detection. Then, the flux residuals are transformed by multi sequence harmonic synchronous rotating transformation and inputted into low pass filters (LPFs) in order to obtain the DC components. Last, offset and gain faults of the two phase current sensors, offset fault of the rotor angle sensor and permanent magnet (PM) demagnetization can be isolated by comparing the DC components and preset thresholds. The detection and isolation strategy of PMSM is validated by motor controller hardware in motor bench tests.

For a practical pad design, a magnetic shielding layer is imperative which is made of ferrite, aluminum or some other metallic material. However, once the magnetic shielding layer is added, not only the mutual inductance but also the self-inductance of the coupling coils vary with the lateral misalignment which is inevitable for a human driver. The change of self-inductance will also result in the mistuning problem in the resonant circuit, which can significantly reduce the transmission efficiency of the whole wireless power transfer (WPT) system. This paper proposed a method of parameter identification of self-inductance based on the least square in order to solve the mistuning problem. In order to verify the proposed method, both the simulation model and the experiment set-up are built.

Calculating accurately iron bridge saturation effects of the magnetic field, for Permanent Magnet Assisted Synchronous Reluctance Motors (PMASynRMs), remains to be a knotty problem. This paper presents an analytical modeling method to predict open-circuit magnetic field distributions and electromagnetic performances of PMASynRMs, considering iron bridge saturation effects. This analytical modeling method combines the magnetic equivalent circuit method, superposition principle, the solution of the governing Maxwell’s field equations and a complex relative permeance function. A quadruple-layer PMASynRM are remodeled into four surface-inserted permanent magnet synchronous motors (SPMSMs) which have different surface-inserted permanent magnets.

An accurate finite element (FE) model is the basis for the numerical prediction of vibration and noise of permanent magnet synchronous motors (PMSMs). This paper provides an equivalent modeling method of PMSMs considering the orthotropic material parameters of the stator system. First, a theoretical analysis of the influence of orthotropic material parameters on modal characteristics is implemented. Subsequently, the influence of orthotropic material parameters on the modal frequency of the stator is analyzed through the FE method. Then, the modal parameters of the stator core and the stator assembly are obtained by modal tests. According to the equivalent FE model and modal parameters, the orthotropic material parameters of the stator system are acquired. Moreover, to save the calculation time and simplify the modal identification process, the influence of windings is taken into account through additional mass and additional stiffness during the modeling process.

As the international community strengthens the control of carbon dioxide emissions, electric vehicles have gradually become a substitute for internal combustion engine vehicles. The battery pack is one of the most important components of electric vehicles. The strength and fatigue performance of the battery support plate not only affect the performance of the vehicle but also concern the safety of the driver. In the present study, the finite element model of a battery pack for fatigue analysis is completely established. The random vibration stress response analysis and acceleration power spectral density response analysis of the support plate for the battery pack are carried out, and the accuracy of the finite element model is verified by a random vibration test.

This study investigated the plastic deformation behavior of 304 stainless steel thin-walled tubes under axial compression by means of numerical calculation and theoretical analysis. It was found that the plastic deformation length of thin-walled tube determined the formability of folds and the work done in the whole axial compression process. To reveal the relation between the range of plastic deformation length and tube geometry parameters, regression equations were established using the quadratic regression orthogonal design method. Experiments were conducted to validate the equations. The process windows for forming a single fold and tube joining at ends had been printed ultimately. The results showed that the regression equations can accurately predict the range of plastic deformation length for forming a single fold.

In this paper, a linear oscillatory actuator (LOA) with moving magnets used in active engine mount is modeled and theoretically analyzed considering its performance decline at high temperature. Firstly, a finite element model (FEM) of the LOA with moving magnets is established. The actuator force is decomposed to ampere force and cogging force through formation mechanism analysis. By using the FEM, ampere forces and cogging forces of the LOA with moving magnets under different current loads and different mover positions are calculated. The FEM and calculation method are validated by bench level test. The voice coil constant and cogging coefficient at normal temperature are identified, which indicates the actuator force is a linear model related to the current and the mover position.

In this paper, an equivalent conversion method is proposed to apply the six-dimensional force road spectrum of the four-axle vehicle on the same platform to the three-axle through the axle load comparison. Further, the feasibility of the devolved equivalent conversion method is verified, and the fatigue performance improvement of the wishbone support structure of a commercial vehicle is finally achieved. Specifically, firstly, the load spectrum at each attachment point of the suspension for the three-axle vehicle is obtained through the iteration of the multi-body dynamic model. Furthermore, the finite element model of the suspension for the three-axle vehicle is established; the analysis of fatigue life for the suspension structure is performed by extracting stress amplitude through the multi-axis cyclic counting method and calculating equivalent force amplitude through McDiarmid’s criterion, combined with the SN curve of the material.

The displacement of the shaft head fails to be accurately measured while the three-axle heavy-duty truck is driving on the reinforced pavement. In order to obtain accurate fatigue load spectrum of the suspension bracket, the acceleration signals of the shaft heads of the suspension obtained by the reinforced pavement test measurement are virtually iterated as responses. A more accurate model of the rigid-flexible coupled multi-body dynamics (MBD) of the whole vehicle is established by introducing a flexible frame based on the comprehensive modal theory. Furthermore, the vertical displacements of the shaft heads are obtained by the reverse solution of the virtual iterative method with well-pleasing precision. The accuracy of the virtual iteration is verified by comparing the simulation results with the vertical acceleration of the shaft head under the reinforced pavement in the time domain and damage domain.

With the growing prosperity of the long-distance freight and urban logistics industry, the demand for cargo trucks is gradually increasing. The connecting bracket is the critical connecting part of the truck chassis, which bears the load transmitted by the road excitation and reduces the damage to the frame caused by the load. However, the occurrence of rough road conditions is inevitable in heavy-duty transportation. In this paper, road durability tests and fatigue life analysis are carried out on the original structure to ensure the safety of the vehicle. Based on the known boundary and load constraints, a lightweight and high-performance structure is obtained through size optimization, as the original structure cannot meet the performance requirements. Firstly, the road test was conducted on the truck where the original bracket structure is located.